Window sills and accessories
Extruded aluminium window sills for outdoor use
Hartmann extruded aluminium window sills. Four different surfaces are available directly from stock. Further surfaces are available upon request - just ask!
|
plain, no prot.film |
RAL 9016, prot.film |
RAL 7016, prot.film |
E6/EV1, prot.film |
|
|---|---|---|---|---|
| 50 |
• |
• | • | • |
| 70 | • | • | • | • |
| 90 | • | • | • | • |
| 110 | • | • | • | • |
| 130 | • | • | • | • |
| 150 | • | • | • | • |
| 165 | • | • | • | • |
| 180 | • | • | • | • |
| 195 | • | • | • | • |
| 210 | • | • | • | • |
| 225 | • | • | • | • |
| 240 | • | • | • | • |
| 260 | • | • | • | • |
| 280 | • | • | • | • |
| 300 | • | • | • | • |
| 320 | • | • | • | • |
| 340 | • | • | • | • |
| 360 | • | • | • | • |
| 380 | • | • | • | • |
| 400 | • | • | • | • |
- Screw-on bar: 25 mm. With slotted holes (4.2 x 7.0 mm) every 300 mm
- Lengths: 6000 mm
- Slope: 5°
- Drip edge: 40 mm
Depths from 400 mm are available upon request, made of rolled sheet.
Accessories
Extensive range of accessories, perfectly matched to the Hartmann window sill range:
End pieces / edging profiles
- For plaster masonry with 17 mm plaster edge
- For clinker brickwork or wooden façades
- For depths from 50 to 400 mm
- Surface plain, RAL 7016, RAL 9016 or E6/EV1 anodised
Straight butt splice connector
- With extra wide cover surface of 35 mm
- For depths 50 - 400 mm
- Surface plain, RAL 7016, RAL 9016 or E6/EV1 anodised
Straight slip joint
- With additional sealing for optimum absorption of linear expansion
- For depths 50 - 400 mm
- Surface plain, RAL 7016, RAL 9016 or E6/EV1 anodised
Sliding end piece with EPDM rubber seal
- For rendered masonry or clinker brickwork
- Thermal expansion is absorbed and the masonry is protected
- Two-part end piece and sealing material
- Tight against driving rain up to 1950 PA
- For depths 50 - 400 mm
- Surface plain, RAL 7016, RAL 9016 or E6/EV1 anodised
Butte splice connector inside corner
- For 90° and 135° corner joints
- On request: Other degrees and drip edge lengths
- For depths 50 - 400 mm
- Surface plain, RAL 7016, RAL 9016 or E6/EV1 anodised
Butte splice connector inside corner
- For 90° and 135° corner joints
- On request: Other degrees and drip edge lengths
- For depths 50 - 400 mm
- Surface plain, RAL 7016, RAL 9016 or E6/EV1 anodised
Vario holder
- Two-part component, consisting of base body and insertion bracket, to compensate for masonry differences
- Prevents the window sill from detaching under high wind loads
- Water accumulation is drained away more quickly and kept away from the masonry
Noise reducing film
- Self-adhesive
- Non-combustible (A2)
- On roll in widths of 50, 75, 100, 150 and 250 mm
Connection seals made of weather-resistant EPDM
Stainless steel screws with plastic sealing disc
Plastic caps for screws
